Service instructionsfor heating engineersVitoflame 200Oil pressure jet burner (type VEK)H up to 40 kW with oil pre-heaterH from 50 kW without oil pre-
Initial start-up and maintenance10Implementation(Cont.)11. Nozzle replacementMaintenance1. Plug the burner chassis withnozzle assembly pointing upward
Initial start-up and maintenance11Implementation(Cont.)12. Checking and adjusting the ignition electrodesMaintenance15 to 33 kW40 to 63 kWCheck igniti
Initial start-up and maintenance12Implementation(Cont.)14. Cleaning or, if necessary, replacing the oil pump filterMaintenanceDanfoss oil pumptype BFP
Initial start-up and maintenance13Implementation(Cont.)16. System start-upMaintenance1. Open the oil filter valve.2. Switch on the mains electricaliso
Initial start-up and maintenance14Burner control unitYou may use the following burnercontrol units with this burner:Burner control unit LOA 14.171B2VH
Initial start-up and maintenance15Burner control unit(Cont.)Burner control unit LMO 14.113A2 (Cont.)H OperationThe reset button ET isthe central contr
Initial start-up and maintenance16Burner control unit(Cont.)Burner control unit LMO 14.113A2 (Cont.)H Fault cause diagnosisThe red signal lamp stays o
Initial start-up and maintenance17Burner control unit(Cont.)Burner control unit LMO 14.113A2 (Cont.)During the fault cause diagnosis, all control outp
Troubleshooting18Procedure overviewDiagnosis 1. Establish fault/ascertain system behaviour.2. Look for the corresponding fault cause in the diagnosis
Troubleshooting19DiagnosisFault/behaviour of the system Cause of fault CheckBurner does not start (without faultdisplay), fault lamp does notilluminat
General Information2Safety instructionsPlease follow these safety instructions closely to avoid the risk of injury to individuals and damage to proper
Troubleshooting20Diagnosis(Cont.)Fault/behaviour of the systemCause of fault CheckBurner starts up and flame isFlame monitor contaminated. Clean the f
Additional information21SpecificationRated output kW 15 18 22 27 33 40 50 63Type of burner VEKI-1 VEKI-1 VEKI-1 VEKI-1 VEKI-1 VEKI-2 VEKII-1 VEKII-2Ty
Additional information22Approximate values for burner settingsPlease note:Check whether the service instructions are valid for the boiler concerned (s
23Platzhalter Bauteilübersicht5692 437 GB
24PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB
25PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrrSSSSttttrrrroooommmmllllaaaauuuuffffppppllllaaaannnn5692 437 GB
26PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB
27PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrrEEEEiiiinnnnzzzzeeeelllltttteeeeiiiilllllllliiiisssstttteeee5692 437 GB
28PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB
29PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB
Contents3PageGeneral informationSafety instructions 2...Appli
30PPPPllllaaaattttzzzzhhhhaaaalllltttteeeerrrr5692 437 GB
Additional information31Maintenance ReportMaintenance/ServiceDate:By:Maintenance/ServiceDate:By:Maintenance/ServiceDate:By:Maintenance/ServiceDate:By:
Viessmann Werke GmbH&CoD-35107 AllendorfTel: (06452) 70-0Fax: (06452) 70-2780www.viessmann.deViessmann LimitedHortonwood 32, TelfordShropshire, TF
Additional informationComponent overview23/245692 437 GBA Air regulating valveB Flame monitor(flicker detector)C Burner control unitD Reset buttonE Co
Additional informationWiring diagramLegendA‘ Start of oil pre-heat timeAStart-upB Timing of flamebeing establishedC Operating positionD Controlled shu
Additional informationParts listWhen ordering spare parts:Quote the type and serial no. (seetype plate) and the item no. of therequired part (as per p
Additional informationParts list(Cont.)Parts019 Impeller020 Oil hose - flow021 Oil hose - return027 Sensor plate030 Nozzle assembly with oilpre-heater
Initial start-up and maintenance4Procedure overviewInitial start-up stepsMaintenance stepsI1. System start-up Page 5...
Initial start-up and maintenance5ImplementationTo obtain the optimum combustion values, it is essential to adjust the burnerwith the boiler heated to
Initial start-up and maintenance6Implementation(Cont.)Initial start-up2. Oil pressure adjustment and vacuum checkMaintenancePlease note:The oil pressu
Initial start-up and maintenance7Implementation(Cont.)Initial start-up3. Air volume fine adjustmentMaintenancePlease note:The oil pressure is preset a
Initial start-up and maintenance8Implementation(Cont.)Initial start-up4. Burner checkMaintenanceRecord all test values in the order ofthe maintenance
Initial start-up and maintenance9Implementation(Cont.)8. Cleaning the burnerMaintenance1. Set the burner to maintenance.2. Clean the housing and the b
Hello! Crazy discounts, hurry up! We are Drop Dead Studio and our goal is to help companies achieve impressive sales results through automated marketing. I. We sell fresh databases for GSA Search Engine Ranker. • The databases are updated monthly through 24/7 parsing and by connecting purchased databases from other sources. • You have the option to purchase a one-time fresh database or pay for a lifetime subscription for updates. ATTENTION! 40% discount only until