Viessmann VITOCAL 222-G Fiche technique Page 168
- Page / 236
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
A Set DHW temperature
B Heat pump switching hysteresis
("Hysteresis")
C Instantaneous heating water hea-
ter switching hysteresis ("Hys-
teresis; DHW E heating")
D Actual DHW temperature at the
upper cylinder temperature sen-
sor
E Heat pump control state
F Control state, instantaneous heat-
ing water heater
G OFF
H ON
Note
The value selected for "Hysteresis"
should be higher than the expected
temperature drop due to heat losses
in a single night (approx. 5 K).
A lower value for "Hysteresis DHW E
heating" increases the proportion of
electrical DHW heating, i.e. the sys-
tem efficiency drops.
Access
&
"Device settings"
&
"Programming"
&
"DHW"
&
"Hysteresis"
&
or
&
"Hysteresis; DHW E heating"
&
(5/%)
Standard setting Setting range
"Hysteresis" 7.0 K 1.0 to 10.0 K
"Hysteresis; DHW E
heating"
10.0 K 2.0 to 30.0 K
Hysteresis; DHW instantaneous heating water . . . (cont.)
168
DHW control settings
5592 969 GB
- VIESMANN 1
- Safety instructions 2
- Safety instructions (cont.) 3
- Installation instructions 4
- Service instructions 4
- Index (cont.) 5
- Positioning 9
- Transport 9
- Positioning (cont.) 10
- Heating circuit 14
- Natural cooling function 15
- Hydraulic diagram 18
- Electrical connection 18
- Equipment required 18
- System version 1 19
- System version 1 (cont.) 20
- System version 2 27
- System version 2 (cont.) 28
- System version 3 36
- System version 3 (cont.) 37
- System version 4 45
- System version 4 (cont.) 46
- Preparing the installation 56
- Heat pump preparation 59
- Heat pump preparation (cont.) 60
- Installing the control module 61
- Inserting the heat pump 62
- Inserting the cables 64
- Inserting the cables (cont.) 65
- Sensor connections 66
- Central fault message 69
- DHW circulation pump 70
- Power supply 74
- Power supply (cont.) 75
- position (like the 89
- Connecting the DHW 94
- Connection panel 94
- Connecting the DHW (cont.) 95
- Connecting the brine side 98
- 5592 969 GB 100
- Removing the front panels 101
- Maintaining service reports 101
- Vitocal 242) 105
- System configuration 109
- Checking the secondary pump 113
- Checking the primary pump 115
- Programming unit overview 123
- Fault messages 123
- Control unit diagnostics 123
- Acknowledging fault messages 124
- Scanning fault messages 124
- Skipping fault messages 125
- Displaying fault messages 125
- Diagnosis 130
- Diagnosis (cont.) 131
- Main menu > Information 134
- A see page 136 B see page 137 135
- C only for the Vitocal 242 135
- Control settings 135
- A see page 135 B see page 137 136
- A see page 138 B see page 140 141
- Adjusting sensor temperatures 143
- Checking signal inputs 144
- "Relay" sub-menu 145
- "Mixer" sub-menu 145
- Power-OFF contact: 1S 147
- System design 147
- Frost protection temperature 149
- Maximum flow temperature 150
- Minimum return temperature 150
- Power-OFF compressor 150
- Min. compressor off 152
- Flow; primary/secondary pump 152
- Minimum runtime 152
- Optimum runtime 153
- Optimum runtime (cont.) 154
- Electric heating 155
- E heating 155
- DHW with electric power 156
- Electric heating (cont.) 156
- Electric heating threshold 157
- Heater rod delay 157
- Time for drying buildings 159
- Internal pump run-on 160
- Max. steps; three-way valve 160
- Flow hysteresis 160
- Maximum temperature 162
- Solar collector 162
- Pump kick hysteresis 163
- Pump kick runtime 164
- Pump kick hysteresis (cont.) 164
- Pump kick dead time 165
- Flow rate 165
- Pump kick runtime (cont.) 165
- DHW program temperature 166
- DHW circulation pump program 166
- Operating mode 166
- DHW cylinder temperature 166
- DHW cylinder maximum 167
- Stop optimisation 169
- DHW auxiliary function 169
- Set DHW temperature 2 169
- Heat pump cylinder volume 169
- Start optimisation 169
- Maximum DHW runtime 170
- Maximum DHW interruption 170
- Excess reaction 170
- Reduced temperature 172
- Remote control 172
- Standard temperature 172
- Minimum flow temperature 173
- Operating mode (cont.) 173
- DHW during party mode 174
- Room temperature sensor 175
- Excess reaction (cont.) 175
- Room temperature hook-up 176
- Room temperature control 177
- Flow T excess 178
- Mixer parameters 179
- Mixer runtime 179
- Screed function 180
- Mixer active zone/dead zone 181
- Screed function (cont.) 181
- V Flow temperature 182
- Vs Set flow temperature 182
- Vh Active zone 182
- Vt Dead zone 182
- Cooling curve level/slope 183
- Natural cooling with mixer 184
- Cooling mixer runtime 185
- Cooling mixer parameters 186
- Buffer cylinder program 187
- Fixed temperature 187
- Buffer cylinder 187
- Hysteresis temperature 188
- Fixed temperature (cont.) 188
- Maximum temperature (cont.) 189
- Sensor resistance curves 191
- Main connection area 194
- Main connection area (cont.) 195
- Safety chain, 400 V units 196
- Safety chain, 230 V units 197
- Left part of the main PCB 198
- R.h. part of the main PCB 202
- Parts list Vitocal 242-G 204
- Parts lists 206
- Parts list Vitocal 222-G 210
- Hydraulic parameter report 216
- Control parameter report 217
- Switching times 219
- Z characteristic required 223
- L and DHW heating 225
- Declaration of conformity 230
- Keyword index 232
- Keyword index (cont.) 233
- Applicability 236
Produits connexes et manuels pour Pompes à chaleur Viessmann VITOCAL 222-G
(10 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.984 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels